2007 toyota highlander manual pdf




















If a door is not opened by then, all the side doors and back door will be automatically locked again. The timing for the automatic door lock function can be changed. The wireless door locking or unlocking function can be erased. You can switch the beep on and off. The beep is on initially and after battery replacement. Insert the ignition key and remove it. Two beep sounds inform you that the program has been switched on or off. If this procedure is not followed exactly, the beep will not operate as expected.

If the beep does not operate as expected, repeat this procedure from step 1. Release the switch and then push again. For replacement, use a CR lithium battery or equivalent. The alarm function can be disabled. The alarm will last for one minute. To stop alarm midway, do the following:!

Unlock any of side door or back door! When replacing the transmitter battery, be careful not to lose the components. Replace only with the same or equivalent type recommended by a Toyota dealer. Dispose of used batteries according to the local laws. Replace the transmitter battery by following these procedures: with the key or wireless remote control transmitter.

Using a coin or equivalent, open the transmitter case. Remove the discharged transmitter battery by ballpoint pen. Insert the tip of ballpoint pen at the guide groove and lift as shown in the above illustration. Close the transmitter case securely. After replacing the battery, check that the transmitter operates properly.

If the transmitter still does not operate properly, contact your Toyota dealer. Do not bend the terminals. Make sure the positive side and negative side of the transmitter battery are faced correctly. Do not replace the battery with wet hands. Water may cause unexpected rust. Do not touch or move any components inside the transmitter, or it may interfere with proper operation.

Be careful not to bend the electrode when inserting the transmitter battery and that dust or oils do not adhere to the transmitter case. To lock: Turn the key forward.

To unlock: Turn the key backward. All the side doors and back door lock and unlock simultaneously with either front door. This double key turning operation to unlock all the side doors and back door can be changed to a single key turning operation. To lock: Push the switch down on the front side. To unlock: Push the switch down on the rear side.

Operating the switch simultaneously locks or unlocks all the side doors and back door. Lock all the side doors and back door with the key or wireless remote control transmitter when all the side doors and back door are closed.

Move the lock knob. To lock: Push the knob forward. To unlock: Pull the knob backward. Closing the side door with the lock knob in the lock position will also lock the side door. Be careful not to lock your keys in the vehicle. The door cannot be locked when either front door is open and the key is in the ignition. Unlock all the side doors and back Before driving, be sure that the doors are closed and locked, especially when small children are in the vehicle.

Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the vehicle in an accident.

It also helps prevent the doors from being opened unintentionally. We recommend using this feature whenever small children are in the vehicle.

Key off operation: If all the side doors and back door are closed, they work for 43 seconds even after the ignition switch is turned off. They stop working when the either front door is opened. Normal operation: The window moves as long as you hold the switch.

To open: Push down the switch. To close: Pull up the switch. The window will fully open or close. To stop the window partway, lightly move the switch in the opposite direction and then release it.

Jam protection function: During automatic closing operation, the window stops and opens half way if something gets caught between the window and window frame.

If the window receives a strong impact, this function may work even if nothing is caught. Never leave anyone particularly a To avoid death or serious personal injury, you must do the following. To open: Turn the key fully backward and hold it. To close: Turn the key fully forward and hold it. After the door is locked or unlocked, the window begins to move.

Operations stop when the key is released. You must also make sure the heads, hands and other parts of the bodies of all occupants are kept completely inside the vehicle. When anyone closes the power windows, make sure he or she operates the windows safely. Unattended person particularly a small child can be involved in a serious accident.

Never try jamming any part of your body to activate the jam protection function intentionally, as it could result in a death or serious injury.

The jam protection function may not work if something gets caught just before the window is fully closed. When small children are in the ve- hicle, never let them use the power window switches without supervision. Use the window lock switch to prevent them from making unexpected use of the switches. Be sure to remove the ignition key when you leave your vehicle. This feature can be disabled. To lock: Turn the key clockwise. To unlock: Turn the key counterclockwise.

To open the back door, pull the lock release lever. When closing the back door, the inside strap can be used to make the reach easier. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is securely closed. Operating the power door lock switch or wireless remote control transmitter simultaneously locks or unlocks the back door.

When closing the back door, make sure it is fully closed. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle. To open the hood: 1. Pull the hood lock release lever. The hood will spring up slightly. In front of the vehicle, pull up the auxiliary catch lever and lift the hood. Otherwise, the hood may open unexpectedly while driving and an accident may occur. Hold the hood open by inserting the support rod into the slot.

Before closing the hood, check to see that you have not forgotten any tools, rags, etc. Then lower the hood and make sure it locks into place. If necessary, press down gently on the front edge to lock it. To deter vehicle theft, the system is designed to sound an alarm if any of the side doors, back door or hood is forcibly unlocked or the battery terminal is disconnected and then reconnected when the system is set.

The alarm blows the horn intermittently and flashes the headlights, tail lights and turn signal lights, and turns on the interior light. The indicator light will start flashing when the key is removed from the ignition switch. Have all passengers get out of the vehicle. Close and lock all the side doors, back door and hood. After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.

The indicator light will remain on when all the side doors, back door and hood are closed and locked. When the system is set, the indicator light will start flashing again. After making sure the indicator light starts flashing, you may leave the vehicle. Never leave anyone in the vehicle when you set the system, because unlocking from the inside will activate the system.

Canceling the system The system will cancel within 30 seconds before the system is set automatically under any of the following conditions:! Any of the side doors, back door or hood is opened. Any of the side doors or back door is unlocked. The key is inserted into the ignition. The battery terminal is reconnected. If the tail lights come on for 2 seconds, the theft deterrent system has been alarmed.

Check to see if there is any abnormality with your vehicle. The system will sound the alarm under the following conditions:! If any of the side doors and back door is unlocked or opened without the key or wireless remote control transmitter, or if the hood is forcibly opened. If the battery terminal is disconnected and then reconnected. Stopping the alarm The alarm will be stopped by the following conditions:!

The indicator light will come on when the system is activated. If any of the side doors and back door is unlocked without the key or wireless remote control transmitter and the key is not in the ignition switch, all the side doors and back door will be automatically locked again.

After about 1 minute, the alarm will automatically stop and the indicator light will start flashing again. Unlock any of the side doors or back door with the key or wireless remote control transmitter.

If the battery becomes discharged due to the vehicle being unused for a long time, etc. If this happens, immediately unlock any of the side doors or back door with the key or the wireless remote control transmitter, and the alarm will stop. Open all the windows. Set the system as described above. The side doors and back door should be locked with the key or wireless remote control transmitter.

Be sure to wait until the indicator light starts flashing. Unlock any door from the inside. The system should activate the alarm. Stop the alarm as described above. Repeat this operation for the other doors and hood. When testing the hood, also check that the system is activated when the battery terminal is disconnected and then reconnected. If the system does not work properly, have it checked by your Toyota dealer.

This indicates that the fuel filler door is on the left side of your vehicle. To open the fuel filler door, pull the lever up. When refueling, turn off the engine. Do not smoke, cause sparks or allow open flames when refueling. The fumes are flammable. When opening the cap, do not remove the cap quickly.

In hot weather, fuel under pressure could cause injury by spraying out of the filler neck if the cap is suddenly removed. Make sure the cap is tightened securely.

The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible. Make sure the cap is installed securely to prevent fuel spillage in the event of an accident. To remove the fuel tank cap, turn the cap slowly counterclockwise, then pause slightly before removing it.

It is not unusual to hear a slight swoosh when the cap is opened. The removed cap can be stored on the back side of the fuel filler door. When installing the cap, turn the cap clockwise until you hear a click. When you hear the click, the cap is fully closed. Use only a genuine Toyota fuel tank cap for replacement. It is designed to regulate fuel tank pressure. Do not pull or pry it. The roof will fully close automatically. The sun shade can be opened or closed by hand. Sliding operation toward the The roof will open and stop partway 45 mm 1.

As driving with the moon roof opened fully will cause wind throbs, we recommend you to drive with the moon roof partway 45 mm 1. When you quickly push and release the switch, the moon roof will open while the switch is depressed and stop when released.

Tilting operation The sun shade will be opened together with the roof. When you quickly push and release the switch, the moon roof will close while the switch is depressed and stop when released. The roof will fully tilt up automatically. When you quickly push and release the switch, the moon roof will tilt up while the switch is depressed and stop when released. The roof will fully tilt down automatically. Key off operation: If all the side doors and back door are closed, it works for 43 seconds even after the ignition switch is turned off.

It stops working when either front door is opened. Jam protection function:! If something gets caught between the moon roof and frame during slide closing operation, the moon roof stops and then opens slightly. If something gets caught between the moon roof and frame during tilting down operation, the moon roof stops and then tilts up fully. If the moon roof receives a strong impact, this function may work even if nothing is caught. Be sure to remove the ignition key To avoid death or serious personal injury, you must do the following.

Never leave anyone particularly a! While the vehicle is moving, always keep the heads, hands and other parts of the bodies of all occupants away from the roof opening. Otherwise, they could be killed or seriously injured if the vehicle stops suddenly or if the vehicle is involved in an accident. Before you close the moon roof, always make sure there is nobody around the moon roof. You must also make sure nobody places his or her head, hands and other parts of the body in the roof opening.

When anyone closes the moon roof, first make sure it is safe to do so. Never sit on top of the vehicle around the roof opening. The jam protection function may not work if something gets caught just before the moon roof is fully closed.

Front seats. Rear seats. Flattening seatbacks. Seat heaters. Head restraints. Seat belts. SRS airbags. Child restraint. Do not drive the vehicle unless the occupants are properly seated. During driving, do not allow any passengers to stand up or move around between seats. Otherwise, death or severe injuries can occur in the event of emergency braking or a collision.

Driver seat! This distance is measured from the center of the steering wheel to your breastbone. If you sit less than mm 10 in. Move your seat to the rear as far seat. Although vehicle designs vary, many drivers can achieve the mm 10 in.

If your steering wheel is adjustable, tilt it downward. This points the airbag toward your chest instead of your head and neck. The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.

The front passenger seat should be as far from the airbag as possible with the seatback adjusted, so the front passenger sits upright. The SRS side airbags are installed in the driver and front passenger seats. Observe the following precautions. Do not lean against the front door! Be careful that the seat does not!

Do not adjust the seat while the when the vehicle is in use, since the side airbag inflates with considerable speed and force. Otherwise, you may be killed or seriously injured. Do not use seat accessories which cover the area where the side airbags inflate. Such accessories may prevent the side airbags from activating correctly, causing death or serious injury. Do not modify or replace the seats or upholstery of the seats with side airbags.

Such change may prevent the side airbag system from activating correctly, disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury. After adjusting the seat position, re- lease the lever and try sliding the seat forward and backward to make sure it is locked in position.

After adjusting the seatback, push your body back against the seat to make sure the seat is locked in position. Do not put objects under the seats. While adjusting the seat, do not put your hands under the seat or near the moving parts. Otherwise, your hands or fingers may be caught and injured.

Then slide the seat to the desired position with slight body pressure and release the lever. Then lean back to the desired angle and release the lever.

The seat belts provide maximum protection in a frontal or rear collision when the driver and the front passenger are sitting up straight and well back in the seats.

If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen or your neck may contact the shoulder belt. In the event of a frontal collision, the more the seat is reclined, the greater the risk of death or serious injury.

Releasing the switch will stop the seat at that position. Do not place anything under the front seats, as this might interfere with the seat movement.

Releasing the switch will stop the seatback at that position. Do not adjust the seat while the 3. The amount of lumbar support will change while the switch is pressed.

When returning the seatback to the vehicle is moving. Be careful that the seat does not hit a passenger or luggage. After adjusting the seat position, re- Make sure the seatback is securely locked by pushing forward and rearward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly. After adjusting the seatback, push Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use.

Be careful not to get your hands or feet pinched in the seat. Folding down the rear seatbacks will enlarge the luggage compartment. Do not adjust the seat while the vehicle is moving. Avoid reclining the seatback any more than needed.

The seat belts provide maximum protection in a frontal or rear collision when the passengers are sitting up straight and well back in the seats. After adjusting the seat position, release the lever and try sliding the seat forward and backward to make sure it is locked in position. For easy access to the third seat: 1. Lift the lever on the side of the seatback and fold the seatback. The seat will slide forward. After passengers are in, lift up the seatback and return the seat until it locks.

Stow the center seat belt buckle of the second seat as shown in the illustration. Vehicles with third seat 2. Make sure the outer seat belts passes through the hangers when folding the second seat.

This prevents the shoulder belt from being damaged. Folding down the second seats will enlarge the luggage compartment. When returning the seatback to the upright position, observe the following precautions in order to prevent death or serious injury in a collision or sudden stop:! Make sure the seatback is securely locked by pushing forward and rearward on the top of the seatback.

Make sure the seat belts are not twisted or caught in the seatback and are arranged in their proper position and are ready to use. After folding down the right side seat, try pushing the seat forward and rearward to make sure it is secured in place.

Right side seat: The seat remains in position when pushing the seat cushion backwards while folding down the seatback. Do not fold the second seat seatback forward with the luggage cover hooks attached. Then lean back to the desired angle and release the strap. When returning the seatback to the upright position, observe the following precautions in order to prevent death or serious injury in a collision or sudden stop: 2. From rear!

Stow the third seat seat belt buckles as shown in the illustration. Pull the seatback angle adjusting strap toward you or pull down the seatback angle adjusting lever to unlock the seatback and fold the seatback down until it locks. To stow the third seat seat belt, first insert tab 1 into the slot and then insert tab 2 into the slot. Make sure the tabs are securely locked in the slot.

From rear Folding down the third seat will enlarge the luggage compartment. Make sure the seat belts are not twisted or caught under the seat and are arranged in their proper position and are ready to use. To flatten the seatbacks, do the following: 1. Then pull the seat forward slightly until it locks. Do not allow passengers to ride on the flattened seat while driving; use the seat in the normal position. After returning the seat to its original position, and seatback to make sure Be certain to 2.

Remove the head restraint. Hold the center of the lever and pull it up. Pull the seatback angle adjusting lever up to unlock and push down the seatback. When returning the seatback to the upright position, be careful not to make yourself hit by the seatback which will bound with considerable spring force. After returning the seat to its original position, be certain to replace the head restraint.

Move the seatback angle adjusting switch backward to flatten the seatback. Do not allow passengers to ride on Occupants must use caution when operating the seat heater because it may make them feel too hot or cause burns at low temperatures erythema, varicella. Use extra caution for; the flattened seat while driving; use the seat in the normal position. After returning the seat to its original position, and seatback to make sure Be certain to try pushing forward and it is secured replace head the seat rearward in place.

At this time, the indicator light will illuminate to indicate the seat heater is operating. To turn off the seat heater, push the switch once again.

Persons who have sensitive skin! Persons who are exhausted! Persons who have taken alcohol or drugs which induce sleep sleeping drug, cold remedy, etc. To prevent the seat overheating, do not use the seat heater with a blanket, cushion, or other insulating objects which cover the seat.

Do not put unevenly weighed objects on the seat and do not stick sharp objects needles, nails, etc. When cleaning the seats, do not use organic substances paint thinner, benzine, alcohol, gasoline, etc.

They may damage the heater and seat surface. To prevent the battery from being discharged, turn the switch off when the engine is not running. Front seats Third seats For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. Front head restraints only—On some models, you can also move the front head restraint forward or backward. If such adjustment is desired, pull or push the base of the head restraint.

To use the armrest, pull it down as shown in the illustrations. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recommended. To prevent damage to the armrest, avoid putting heavy loads on it. Adjust the center of the head restraint so that it is closest to the top of your ears.

Front seats! After adjusting the head restraint, make sure it is locked in position. Do not drive with the head restraints removed. The seat belts provided for your vehicle are designed for people of adult size, large enough to properly wear them. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.

If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid inflation of the airbag may cause death or serious injury to the child. Do not allow any children to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious injury or death during emergency braking or a collision.

Also, do not let the child sit on your lap. Holding a child in your arms does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt.

Ask your doctor for specific recommendations. The lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Depending on the injury, first check with your doctor for specific recommendations. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision.

When using the seat belts, observe the following:! Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. This feature is used to hold the child restraint system securely. To free the belt again, fully retract the belt and then pull the belt out once more. Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or doors.

Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be replaced. Do not disassemble or modify the system. Keep the belts clean and dry. If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive cleaners, or allow them to come into contact with the belts—they may severely weaken the belts. Replace the belt assembly includ- ing bolts if it has been used in a severe impact.

The entire assembly should be replaced even if damage is not obvious. Tab If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor. Buckle Adjust the seat as needed and sit straight and well back in the seat.

The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely. After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

Do not insert coins, clips, etc. If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed, because it cannot protect an adult occupant or your child from death or serious injury. Keep the lap belt positioned as low on hips as possible. Do not place the shoulder belt un- Keep as low on hips as possible Adjust the position shoulder belts.

Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. Close the door. Parking brake is not released. Release the parking brake. Oil change is nearly due. Check engine oil.

Oil change is due. Change engine oil. Moonroof is open. Close the moonroof. Fuel door is left open. Close the fuel door. OMU Page The system must be reset after the en- gine oil change. OMU Page Vehicle stability control function If the washer fluid level is low, the mes- sage appears with the master warning light and warning tone when the ignition is on. If the message appears, have the ve- hicle checked by a Toyota dealer as soon as possible. When you start the vehicle with the fuel door left open after refueling.

When you leave the fuel door open for more than 30 minutes during refueling. Shift while holding the lock release button in. Shift normally. Never shift into reverse while the ve- hicle is moving. If the slip indicator light does not come on when the ignition is turned on, contact your Toyota dealer.

OMU Page In situations where the road surface is covered with ice or snow, your vehicle should be fitted with snow tires or tire chains. Always drive at a moderate speed. OMU Page Parking Brake Before driving, be sure the parking transmission to use engine braking brake is fully released and the park- to slow down.

OMU Page Each trol is turned on again. You can now take your foot off the accelerator pedal. Do not use an adaptor for compact disc singles—it could cause tracking errors or interfere with the ejection of compact discs. Allow the player to cool down. OMU Page The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station.

To stop scanning, push this button again. OMU Page In addition, the feature may not work well radio switches from stereo to mono recep- with some spoken word, live, or classical tion.

OMU Page The rest of the title will appear. Turn the knob counter- clockwise to step down the frequency. OMU Page To eject the current compact disc, push and release the compact disc eject button. OMU Page This system lid of separate unit is open. Close the allows you to set twelve FM, two for each compact disc changer lid. OMU Page The radio will find the next station up with some spoken word, live, or classical the station band, stay there for 5 seconds, recordings.

OMU Page Do this again to find tracks remaining on the current side of the next station. Rear seat entertainment system display 5. Rear seat entertainment system controller 6. Input terminal adapter 7. Power outlet main switch 9. OMU Page You can enjoy videos and sound when creased, before you turn on the your personal audio system is connected headphone.

To reduce the chance of injury in case of an accident or sudden stop while driving, close the display when it is not in use. These conditions could cause case to deform or the battery to ex- plode or leak. Remove the cover of the controller 2. Remove the insulating sheet. OMU Page To reduce the chance of injury in case of an accident or a sudden stop while driving, stow the controller in the console box or front seatback pocket when it is not in use.

OMU Page This device may not cause harmful sound. OMU Page This button causes the display to use ated. This button indicates the title search screen when the DVD player is oper- ated. OMU Page This button also can be used when you lose sight of the controller. Joystick This joystick selects a control switch, mode switch on the screen or the menu for the disc. When the front audio system is turned off, the rear audio system and the DVD player will be turned off simultaneously.

OMU Page If the mode display is gray, it cannot be selected. OMU Page The station frequency will appear on the screen. The screen shows the track, or track and disc number currently being played. Use this button to skip up or down to locate a song or recording. OMU Page Toyota dealer. Remove the cover of the controller as shown. Eject the disc. Set the disc again. If the malfunction still exists, take your vehicle to your Toyota dealer.

OMU Page If a disc which is not playable is inserted, compact discs. OMU Page 4. OMU Page As audio will not play in this case, verify that the video tracks are play- ing and then activate playback. For the operation of the menu screen, see the separate manual for the DVD disc. The player starts playing the disc from the selected bonus group number. The selected subtitle language will appear on the screen.

The selected audio language will appear on the screen. The angle number which you can select will appear on the screen. OMU Page You can change the initial setting. After the setting is done, the player plays from the beginning of the chapter or the track. Audio Lang. Push the language code you want to read again. OMU Page To stop scanning, push this switch again. If the player has scanned all the tracks on the disc, it will stop scanning. OMU Page in this Section for details.

When the track ends, it will automatically replay. To turn off the re- peat feature, push this switch again. You can also select the video mode on the mode selection screen mentioned above. Usually, one piece of a movie, one album, or one audio program is assigned as a title. Chapter: A unit smaller than a title. A title comprises plural chapters. Please contact your Toyota dealer for fur- ther details. OMU Page Store cassettes in their cases and out cal motors.

This results in static. The following products may not be playable on your compact disc player. OMU Page Remove discs from the compact disc player when you are not listening to them. Store them in their plastic cases away from moisture, heat, and direct sunlight. Air intake selector 2. Air flow selector 4. Temperature selector 5. Recirculate—Recirculates the air inside the vehicle. Fresh—Draws outside air into the sys- tem.

Fan speed selector 4. Windshield air flow button 7. OMU Page 3. Floor—Air flows mainly from the floor another fan speed mode. Fresh—Draws outside air into the sys- possible select tem.

Pressing the button once again returns the air flow mode to the last one used. OMU Page Toyota dealer for service. To prevent fogging up of the windshield, the air intake mode may change automati- cally to FRESH depending on the condi- tion of the air conditioning system.

This is to clean up the front view more quickly. If air flow control is not satisfactory, check the side vents. The side vents may be opened or closed as shown. Rear heater vents Air flows from the vents when the rear heater system is operating.

OMU Page Air Conditioning Filter The air conditioning filter prevents dust from entering the vehicle through the air conditioning vent.

Open the glove box and push each 3. Pull the filter cover toward you and screwdriver. Remove the filter case toward you. OMU Page The air filter should be installed prop- erly in position. The use of air condi- tioning with the air filter removed may cause deteriorated dustproof per- formance and then affect air condi- tioning performance.

Current fuel consumption The current fuel consumption is calcu- lated and displayed based on distance and fuel consumption for 2 seconds with the hybrid system turned on. Current fuel consumption the procedure.

OMU Page The outside temperature is also displayed utes is displayed. The segment of the battery on the screen indicates the status of the hybrid battery. The ignition switch is turned off imme- diately after turning.

The vehicle is on an inclined surface. Be sure to adjust the display only when the vehicle is stopped. CAUTION To reduce the chance of injury in case of an accident or sudden stop while driving, always completely close the ashtray after use. With the instrument panel lights on, the glove box light will come on when the globe box is open. Decide which of 3 HomeLink buttons doors, gates, entry doors, door locks, in view while programming.

OMU Page After you remove the luggage cover, stow open the center deck board. This will prevent passengers from injury in the event of a sudden stop or accident. RAILS: 1. Turn the upper and side knobs coun- terclockwise loosen cross rails. OMU Page Floor Mat Lock floor mat slips and interferes with the the clips into the holes in the vehicle movement of the pedals during driv- carpet.

OMU Page Utility Vehicle Precautions Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneu- vers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle cor- rectly. Also, hicle can tip over sideways much this can increase maintenance costs. If you continue to have unacceptable driveability, try changing gasoline brands. If this does not rectify your problem, then consult your Toyota dealer. Do not idle or park your vehicle over anything that might burn easi- ly such as grass, leaves, paper or rags.

Have your brakes fixed immediately. OMU Page Brake Pad Wear Limit Indicators If you hear a squealing or scraping noise while driving, have brake pads checked and replaced by your Toyota dealer as soon as possible. Expensive ro- tor damage can result if the pads are not replaced when necessary. It is used in registering the ownership of your vehicle. Manufacturing week 7.

OMU Page 7. Reinforcing rubber 4. Wheel diameter in inches 8. Carcass 5. Load index 2 digits or 3 digits 9. Rim lines 6. Speed symbol alphabet with one Bead wires letter OMU Page Quality grades can be found where appli- cable on the tire sidewall between tread shoulder and maximum sec- tion width.

OMU Page Excessive speed, underinfla- tion, or excessive loading, either sep- arately or in combination, can cause heat buildup and possible tire failure. Total load capacity: kg lb. Car covers are warranted for 12 months from the date of purchase and do not assume any coverage under the Toyota New Vehicle Limited Warranty.

You can save this vehicle to My Garage by simply signing in or creating a new account. The service is currently unavailable. Please check back later. All information contained herein applies to vehicles registered in the 48 U. Try again in a moment. Warranty and Maintenance Guides.

Sorry, our site is temporarily unavailable. Create an account and get the most out of your Toyota today. Additional Resources To view or download additional manuals that take you down to the nuts and bolts manul most Toyota models from and beyond, you may subscribe to our Technical Information System TIS at https: Accessories Warranty Genuine Toyota Parts are built to the highest standards of quality, durability and performance.

The HV battery may have longer mabual under emissions warranty. For accessories purchased after the new vehicle purchase, the coverage is 12 months, regardless of mileage, from the date the accessory was installed on the vehicle, or the remainder of any applicable new vehicle warranty, whichever provides greater coverage, with the exception of car covers. This website uses cookies to improve your experience while you navigate through the website.



0コメント

  • 1000 / 1000